Direct tv multi satellite setup

With DIRECTV you will also get access to over channels in HD, the most exciting sports packages, digital music, international programming and other exclusive content that you can't get with your current cable or satellite provider. Your current residence might already be wired so upgrading most likely be simple and seamless, with the transition bringing higher quality picture and sound and more channels for happier residents and easy installation.

With new technical innovations you can now provide DIRECTV programming access and services from one central dish system to all of your residents. Give residents even more reason to stay by offering smaller programming package prices than if they tried to get it by themselves.

Not only will this entice residence to stay longer but it can also attract new tenants; moving can be a hassle, and if DIRECTV television and other services are already set up, they can be quite the attraction when advertising your properties to prospective tenants, renters, even buyers if you run a condo association. D2 Advantage Lite is a cost effective program for buildings with units. With this service there will only be one satellite dish mounted and this will cover all of your residents, no need for multiple satellite dishes.

TV, Phone and Internet service are able to all come through a single wire into each unit and can use wiring that is already installed on the property. Bundled with a low-cost or no-cost installation this is one of the best solutions anyone can offer. Find an appropriate location for your satellite receiver.

Look for a clear, southern-facing area with a high vantage spot. Find coordinates for pointing your dish to get reception. Connect your satellite receiver to the TV as specified in the receiver's manual. Connect both the television and satellite receiver to a power outlet. Turn them both on. If there is no switch, turn to UHF channel 14 or channel number 65 on cable.

Navigate the menu using buttons on the receiver's front panel and the receiver's manual to find the correct azimuth horizontal and elevation vertical coordinates. Determine and survey the dish's exact mounting site. Using the receiver's pointing coordinates, find the mounting site for your dish.

Measure the number of feet meters of cable needed to finish the installation. Start assembling the satellite receiver dish. Bolt or screw in the satellite's plastic or metal reflector to its support arm. This lets you preset the satellite to its correct elevation. Mount the mast, or pole, for the receiver.

Multiple options exist for this step depending on where you install the dish roof, hollow wall, on brick or concrete, etc. Consult the self-installation guide to see instructions and the necessary tools for each option. Make sure the mast is level to get a satellite signal. Use a bubble level to help you determine it is even. Put the satellite receiver dish on its mast. Attach the LNB to the receiver's support arm. Position a grounding block as closely as you can to the place where the dish's cable will run into the house.

Run the receiver dish's cable to the grounding block. The connection to the block binds the dish to an acceptable grounded point in the main building ground, such as an enclosure for electrical service equipment or a metallic service raceway. Run the RG-6 coaxial cable to the back of the receiver inside the house. The RG-6 cable should also be connected to the grounding block.

Make sure a landline phone is off its hook to avoid getting an electric shock from any incoming calls. Connect the receiver to a phone jack with the phone line. Check for a signal using the "Dish Pointing" menu's signal meter displayed on your TV screen. Adjust the dish's pointing to achieve your maximum signal strength. It depends on the connector on your surround sound system and your receiver sound.

You will need to buy a wire that has a port compatible with your receiver in one end and with your sound system on the other end. Yes No. Not Helpful 1 Helpful 2. It depends on what you call a pole. The dish needs to be mounted to a non-moving object. If your pole is like a wood 4x4, or a 2" diameter metal pole securely held into the ground with concrete, you should have no problems. When you mount the dish to a pole, the dish should not move at all. Mine is mounted on an 8 ft 4x4 wooden post pole placed in a 3 ft deep post hole.

After verifying the post was level, it was backfilled with dirt and inches of concrete. Not Helpful 0 Helpful 1. Include your email address to get a message when this question is answered. Submit a Tip All tip submissions are carefully reviewed before being published.

You Might Also Like How to.